Galvanization Protection Page 2

Maintenance Q & A — March 2001
By Capt. Ken Kreisler

Calculating Amp-Hour Ratings

Part 2: March Maintenance Q & A continued.

 More of this Feature
• Part 1: Galvanization Protection, PWC starter problems, bending copper line
• Part 2: Calculating amp-hour ratings, cutting fiberglass cloth, and more
 Related Resources
• Maintenance Q & A Index
• Maintenance Editorial

What is an amp-hour rating, and how is it calculated? L.B., via e-mail

An amp-hour (Ah) is a unit of measure of a battery’s electrical storage capacity and is based on the total number of amperes a battery can supply in a 20-hour period of constant load. You calculate the amp-hour rating by multiplying the current draw in amperes by the time in hours a battery can supply it. For example, a battery that can deliver 5 amps over 20 hours has a rating of 100 Ah.

However, all of a battery’s capacity is rarely available, due to factors such as age, low ambient temperature, and state of charge, so as a rule of thumb, consider the real Ah rating to be 75 percent of the calculated Ah.

I’m having difficulty cutting straight lines across pieces of plain-weave (O degrees to 90 degrees) fiberglass fabric that I am using for a project. Do you have any suggestions?
A.M., via e-mail

Locate a single fiberglass strand that runs across the entire fabric. Grab one end and pull it out while firmly holding the opposite side of the fabric. If you can’t get a grip with your fingers, try using a small needle-nose pliers. If you still can’t grab one, you may have to cut a small slit in one side to expose more strands. Once you’ve removed the single strand, you will see a clear path across for your shears to follow.

How important is the acid-alkali balance of diesel-engine coolant? T.W., via e-mail

Very. Acid-alkali balance refers to the coolant’s pH, and an improper one can result in degradation of certain metals within the cooling system, even if the proper ratio of coolant to water is present. You can measure your coolant’s pH by using a standard home pool-testing kit or litmus paper.

Typical pH levels range from 1 to 14, and most engine manufacturers recommend a cooling system pH between 8.5 and 10.5 (check your owner’s manual). If the level is above 11.0, the coolant is alkaline and will attack aluminum, copper, and nonferrous metals (those containing no iron). If the pH is below 7.0, the coolant is acidic and will attack ferrous metals.

Because temperature affects pH—at higher temperatures pH is generally lower—it is important to keep your cooling system at the proper operating temperature. Check your coolant temperature gauge frequently, and maintain the recommended coolant-water ratio.

Do you have any tips for removing drips, runs, and stray bristles from a paint job that is already dry?
A.S., via e-mail

If the paint is fully dry, fine sanding or a gentle scraping is the way to go. Once you’ve removed the imperfection, wipe the area clean and repaint. If the paint is still tacky, however, hold a piece of masking tape at both ends and press it gently over the flaw, then pull it off. When the paint is hard and dry, sand the area smooth, wipe, and repaint.
Need help with a maintenance problem? Write to Maintenance Q & A,
Power & Motoryacht, 260 Madison Ave., 8th Fl., New York, NY 10016. Fax: (917) 256-2282. e-mail: No phone calls, please.

Previous page > March 2001 Maintenance Q & A, Part 1 > Page 1, 2

This article originally appeared in the January 2003 issue of Power & Motoryacht magazine.

Vetus Maxwell Tip of the Week

Hot Today

Featured Brands

Costa Palmos logo MCY logo
HMY Yacht Sales logo Volvo Penta logo
Absolute logo Sunseeker

Boat-Name Generator

cube puzzel Thinking of a unique name for your new boat can be tough, that's why we created a Boat Name Generator.
Try it here. ▶

Select Brokerage